How to change a motorcycle tyre

How to change a motorcycle tyre

This tutorial shows you how to change a motocross tyre or an off-road motorcycle tyre for any other activity (Enduro, Trial, Rally raid, Cross Country).

Please note that it is not recommended to change a motorcycle tyre for road use by yourself as it is a more complex procedure that requires wheel balancing. If you want to change a road tyre, please contact a professional. You can find a professional near you here.

Contents of the article:

Accessories for changing your motorcycle tyre

mo 127 tire michelin starcross 6 hard en product in context 1 nosignature square
  • 2 tyre spoons (3 is better)
  • 1 tyre mounting lubricant (air-drying like soapy water; do not use grease as it may cause the rim to spin and the valve to tear off)
  • 1 tyre pressure gauge, if you have an inner tube
  • 1 valve core remover, if you have an inner tube (optional)
  • 1 damp cloth (optional)
  • 1 lever arm (optional)
  • 1 pair of gloves (optional)


Unless you are equipped with a wheel change stand, you can perform these steps on the floor on a cardboard box so as not to damage the side of the wheel that will face the ground. Caution: As the crown is fragile, start with the wheel placed on the opposite side. When you need to turn the wheel over, place the disc on a layer of rags to protect it. We will first look at how to change a motorcycle tyre when it has an inner tube. We will then see how to proceed when it contains the MICHELIN Bib MousseTM.

1 - How to change a motorcycle tyre if you have an inner tube:

1. Remove the valve cap
2. Press down on the valve core to deflate the inner tube (or use the valve core remover to get all the air out of the tyre)
3. Unscrew the valve completely
4. Unscrew the gripster screw a bit to release the tyre
5. Remove the sidewall from both sides of the tyre with a lever arm (or press hard on to loosen it)
6. Use a tyre spoon to remove the tyre from the rim around the entire circumference
7. Pull out the inner tube completely
8. Now use the tyre spoon to pull the tyre out of the rim and clamp it under the disc
9. Use a second tyre spoon to do the same operation about 15 cm further on. Clamp it under the disc and remove the first one.
10. Continue in this way, alternating between the two tyre spoons, until you have pulled the edge of the tyre out of the rim all the way round
11. Turn the wheel over

12. Apply lubricant to the edge of the tyre on the remaining side
13. Repeat step 6 and from 8 to 10
14. Pass a tyre spoon between the tyre and the lower part of the rim and lever the tyre out all the way around (make sure that the tyre on one side is at the bottom of the rim to better extract the other side with the tyre spoon)
15. Clean the inside of the rim with a damp cloth
16. Check the rim base; change it if it is damaged, otherwise there is a risk of damage to the inner tube
17. Put the new tyre on the rim (make sure the direction of rotation is correct)
18. Place the inner tube inside, so that the valve is facing the hole
19. If you have removed the valve core with the valve core remover, put it back into the valve
20. Inject some air into the tube so that it is not completely empty, but still has some flexibility
21. Apply lubricant to the edges of the tyre on both sides
22. Use a tyre spoon to put the tyre back on around the whole circumference by inserting it between the tyre and the lower edge of the rim and levering it out

23. Insert the valve into the rim hole and tighten the nut to 3/4
24. Use a tyre spoon to pull in part of the tyre and wedge it under the crown
25. Use another tyre spoon to pull the tyre in, little by little. Towards the end, if necessary, use the third tyre spoon, also wedging it under the disc to help hold the edge of the retracted tyre. Make sure that the opposite part is at the bottom of the rim.
26. Turn the wheel over and inspect the other side to see if the rim fits all the way around
27. Remove the shell and inflate to properly seat the tyre beads on the rim
28. Put the shell back
29. Make sure the tyre is centred on the rim
30. Fully tighten the gripster screw and the valve screw
31. Using the compressor, inflate the tyre to the recommended pressure
32. Replace the valve cap to protect it from dirt and to ensure a better seal.

2 - How to change a motorcycle tyre if you have the MICHELIN Bib MousseTM

If you want to change a motorcycle tyre equipped with the MICHELIN Bib MousseTM, the steps from 4 to 14 are the same as for an inner tube except that with a MICHELIN Bib MousseTM there are 2 gripsters to unscrew (or even 3 for a MICHELIN Bib MousseTM M18 in a MICHELIN Enduro Xtrem tyre in (140/80 - 18))

michelin bib mousse packaging mockup
3528700573374 tire michelin bib mousse 120 slash 70 12 51s c main 1 30 nopad

Then
1. Remove the MICHELIN Bib MousseTM with the tyre spoon
2. Inspect it to make sure it is in good condition
3. Clean it with a clean cloth
4. Clean the inside of the rim with a damp cloth
5. Check the rim base; change it if damaged, otherwise there is a risk of damaging the MICHELIN Bib MousseTM

6. Apply the MICHELIN lubricant gel supplied with the MICHELIN Bib MousseTM (1 tube for a rear tyre, ½ for a front tyre) and use a brush to apply it to the inside of the new tyre (don’t apply it on edges)
7. Insert the MICHELIN Bib MousseTM (in order to spread the lower area of the tyre, you can sit on the tyre to facilitate insertion)
8. Apply lubricant to the edges of the tyre on both sides
9. Before mounting the tyre on the rim, make sure the direction of rotation is correct
10. Use a tyre spoon to put the tyre back on the whole circumference by inserting it between the tyre and the lower edge of the rim and by levering

11. Use a tyre spoon to pull in part of the tyre and wedge it under the crown
12. Use another tyre spoon to pull the tyre in little by little. Towards the end, if necessary, use the third tyre spoon, also wedging it under the disc to help hold the edge of the retracted tyre
13. Turn the wheel over and inspect the other side to see if the edge fits tightly all around
14. Make sure the tyre is correctly centred. If it is not, use a tyre spoon and tyre mounting lubricant to help centre the tyre
15. Fully tighten the gripsters' screws

Why choose the MICHELIN Bib MousseTM instead of an inner tube?

MICHELIN Bib MousseTM is the Michelin's off road solution to tyre punctures. It is lighter than a reinforced inner tube and eliminates the inconvenience of a puncture when riding off-road.

Discover all the benefits of the MICHELIN Bib MousseTM

map search desktop

Find a tyre dealer near you in seconds

Search by
Address, City or ZIP code
Motorbike
Locate me
Search
You are using an unsupported web browser
You are using a website browser that is not supported by this website. This means that some functionnality may not work as intented. This may result in strange behaviors when browsing round. Use or updgrade/install one of the following browsers to take full advantage of this website